Wear and corrosion behaviour of Ti–13Nb–13Zr and Ti–6Al–4V alloys in simulated physiological solution
► Ti–13Nb–13Zr wear resistance is substantially lower than that of Ti–6Al–4V alloy. ► Wear of both alloys occurs by adhesion and abrasion, which operate simultaneously. ► Both alloys exhibit spontaneous passivity in Ringer’s solution at 37 °C. ► Corrosion resistance of martensitic Ti–6Al–4V and Ti–1...
Gespeichert in:
| Veröffentlicht in: | Corrosion science 2011-02, Vol.53 (2), p.796-808 |
|---|---|
| Hauptverfasser: | , , , , |
| Format: | Artikel |
| Sprache: | eng |
| Schlagworte: | |
| Online-Zugang: | Volltext |
| Tags: |
Tag hinzufügen
Keine Tags, Fügen Sie den ersten Tag hinzu!
|
| container_end_page | 808 |
|---|---|
| container_issue | 2 |
| container_start_page | 796 |
| container_title | Corrosion science |
| container_volume | 53 |
| creator | Cvijović-Alagić, I. Cvijović, Z. Mitrović, S. Panić, V. Rakin, M. |
| description | ► Ti–13Nb–13Zr wear resistance is substantially lower than that of Ti–6Al–4V alloy. ► Wear of both alloys occurs by adhesion and abrasion, which operate simultaneously. ► Both alloys exhibit spontaneous passivity in Ringer’s solution at 37
°C. ► Corrosion resistance of martensitic Ti–6Al–4V and Ti–13Nb–13Zr alloys are very similar and improved in comparison to the two-phase (α
+
β) Ti–6Al–4V alloy. ► Ti–6Al–4V alloy with martensitic microstructure displays the best combination of both corrosion and wear resistance.
Wear and corrosion behaviour of cold-rolled Ti–13Nb–13Zr alloy, with martensitic microstructure, and Ti–6Al–4V ELI alloy, in martensitic and two-phase (α
+
β) microstructural conditions, was studied in a Ringer’s solution. The wear experiments were performed at room temperature with a normal load of 40
N and sliding speeds 0.26, 0.5 and 1.0
m/s. The corrosion behaviour was studied at 37
°C using open circuit potential-time measurements and potentiodynamic polarization. It was found that Ti–13Nb–13Zr alloy has a substantially lower wear resistance than Ti–6Al–4V ELI alloy in both microstructural conditions. Surface damage extent increases with sliding speed increase and is always smallest for martensitic Ti–6Al–4V ELI alloy with highest hardness. Both alloys exhibit spontaneous passivity in Ringer’s solution. Corrosion potential values are similar for all three materials. However, Ti–13Nb–13Zr and martensitic Ti–6Al–4V ELI alloys show improved corrosion resistance comparatively to Ti–6Al–4V ELI alloy with (α
+
β) microstructure. Martensitic Ti–6Al–4V ELI alloy possesses the best combination of both corrosion and wear resistance, although its corrosion resistance is found to be slightly higher than that of the Ti–13Nb–13Zr alloy. |
| doi_str_mv | 10.1016/j.corsci.2010.11.014 |
| format | Article |
| fullrecord | <record><control><sourceid>proquest_cross</sourceid><recordid>TN_cdi_proquest_miscellaneous_864408703</recordid><sourceformat>XML</sourceformat><sourcesystem>PC</sourcesystem><els_id>S0010938X10005597</els_id><sourcerecordid>1671493897</sourcerecordid><originalsourceid>FETCH-LOGICAL-c401t-d730d433535b015efe6cd46e80d0bc6baeaf6be7f29873e2da3b2ecacdd7ef633</originalsourceid><addsrcrecordid>eNp9kc9O3DAQxq2qlbqlfQMOvqByyXYce53kUgkh_lRCcKF_xMVy7Al45Y0XO0HaG-_AG_IkdQjiyMUjjX_zjeb7CNlnsGTA5I_10oSYjFuWMLXYEpj4QBasrpoCRCM_kgXkn6Lh9b_P5EtKawCY2AXZ_EUdqe4tzRIxJBd62uKdfnBhjDR09No9Pz4xftm-lJuZfWnKI59f8Ydq78MuUdfT5Daj1wNaur3bZS0fbp3RnqbgxyFLfyWfOu0Tfnute-T36cn18XlxcXX26_joojAC2FDYioMVnK_4qgW2wg6lsUJiDRZaI1uNupMtVl3Z1BXH0mrelmi0sbbCTnK-R77PutsY7kdMg9q4ZNB73WMYk6qlEFBXMJGH75JMVkxk35oqo2JGTfYpRezUNrqNjjvFQE05qLWac1CTt4oxlXPIYwevG3TKXnRR98alt9mS52NZIzP3c-YwG_PgMKqshL1B6yKaQdng3l_0H0ZRpKg</addsrcrecordid><sourcetype>Aggregation Database</sourcetype><iscdi>true</iscdi><recordtype>article</recordtype><pqid>1671493897</pqid></control><display><type>article</type><title>Wear and corrosion behaviour of Ti–13Nb–13Zr and Ti–6Al–4V alloys in simulated physiological solution</title><source>Elsevier ScienceDirect Journals</source><creator>Cvijović-Alagić, I. ; Cvijović, Z. ; Mitrović, S. ; Panić, V. ; Rakin, M.</creator><creatorcontrib>Cvijović-Alagić, I. ; Cvijović, Z. ; Mitrović, S. ; Panić, V. ; Rakin, M.</creatorcontrib><description>► Ti–13Nb–13Zr wear resistance is substantially lower than that of Ti–6Al–4V alloy. ► Wear of both alloys occurs by adhesion and abrasion, which operate simultaneously. ► Both alloys exhibit spontaneous passivity in Ringer’s solution at 37
°C. ► Corrosion resistance of martensitic Ti–6Al–4V and Ti–13Nb–13Zr alloys are very similar and improved in comparison to the two-phase (α
+
β) Ti–6Al–4V alloy. ► Ti–6Al–4V alloy with martensitic microstructure displays the best combination of both corrosion and wear resistance.
Wear and corrosion behaviour of cold-rolled Ti–13Nb–13Zr alloy, with martensitic microstructure, and Ti–6Al–4V ELI alloy, in martensitic and two-phase (α
+
β) microstructural conditions, was studied in a Ringer’s solution. The wear experiments were performed at room temperature with a normal load of 40
N and sliding speeds 0.26, 0.5 and 1.0
m/s. The corrosion behaviour was studied at 37
°C using open circuit potential-time measurements and potentiodynamic polarization. It was found that Ti–13Nb–13Zr alloy has a substantially lower wear resistance than Ti–6Al–4V ELI alloy in both microstructural conditions. Surface damage extent increases with sliding speed increase and is always smallest for martensitic Ti–6Al–4V ELI alloy with highest hardness. Both alloys exhibit spontaneous passivity in Ringer’s solution. Corrosion potential values are similar for all three materials. However, Ti–13Nb–13Zr and martensitic Ti–6Al–4V ELI alloys show improved corrosion resistance comparatively to Ti–6Al–4V ELI alloy with (α
+
β) microstructure. Martensitic Ti–6Al–4V ELI alloy possesses the best combination of both corrosion and wear resistance, although its corrosion resistance is found to be slightly higher than that of the Ti–13Nb–13Zr alloy.</description><identifier>ISSN: 0010-938X</identifier><identifier>EISSN: 1879-0496</identifier><identifier>DOI: 10.1016/j.corsci.2010.11.014</identifier><identifier>CODEN: CRRSAA</identifier><language>eng</language><publisher>Kidlington: Elsevier Ltd</publisher><subject>A. Ringer’s solution ; A. Ti orthopaedic alloys ; Abrasion resistance ; Abrasion resistant alloys ; Alloys ; Applied sciences ; C. Corrosion resistance ; C. Microstructures ; C. Wear rate ; Contact of materials. Friction. Wear ; Corrosion ; Corrosion environments ; Corrosive wear ; Exact sciences and technology ; Mechanical properties and methods of testing. Rheology. Fracture mechanics. Tribology ; Metals. Metallurgy ; Microstructure ; Titanium base alloys ; Wear resistance</subject><ispartof>Corrosion science, 2011-02, Vol.53 (2), p.796-808</ispartof><rights>2010 Elsevier Ltd</rights><rights>2015 INIST-CNRS</rights><lds50>peer_reviewed</lds50><woscitedreferencessubscribed>false</woscitedreferencessubscribed><citedby>FETCH-LOGICAL-c401t-d730d433535b015efe6cd46e80d0bc6baeaf6be7f29873e2da3b2ecacdd7ef633</citedby><cites>FETCH-LOGICAL-c401t-d730d433535b015efe6cd46e80d0bc6baeaf6be7f29873e2da3b2ecacdd7ef633</cites></display><links><openurl>$$Topenurl_article</openurl><openurlfulltext>$$Topenurlfull_article</openurlfulltext><thumbnail>$$Tsyndetics_thumb_exl</thumbnail><linktohtml>$$Uhttps://www.sciencedirect.com/science/article/pii/S0010938X10005597$$EHTML$$P50$$Gelsevier$$H</linktohtml><link.rule.ids>314,776,780,3537,27901,27902,65306</link.rule.ids><backlink>$$Uhttp://pascal-francis.inist.fr/vibad/index.php?action=getRecordDetail&idt=23730196$$DView record in Pascal Francis$$Hfree_for_read</backlink></links><search><creatorcontrib>Cvijović-Alagić, I.</creatorcontrib><creatorcontrib>Cvijović, Z.</creatorcontrib><creatorcontrib>Mitrović, S.</creatorcontrib><creatorcontrib>Panić, V.</creatorcontrib><creatorcontrib>Rakin, M.</creatorcontrib><title>Wear and corrosion behaviour of Ti–13Nb–13Zr and Ti–6Al–4V alloys in simulated physiological solution</title><title>Corrosion science</title><description>► Ti–13Nb–13Zr wear resistance is substantially lower than that of Ti–6Al–4V alloy. ► Wear of both alloys occurs by adhesion and abrasion, which operate simultaneously. ► Both alloys exhibit spontaneous passivity in Ringer’s solution at 37
°C. ► Corrosion resistance of martensitic Ti–6Al–4V and Ti–13Nb–13Zr alloys are very similar and improved in comparison to the two-phase (α
+
β) Ti–6Al–4V alloy. ► Ti–6Al–4V alloy with martensitic microstructure displays the best combination of both corrosion and wear resistance.
Wear and corrosion behaviour of cold-rolled Ti–13Nb–13Zr alloy, with martensitic microstructure, and Ti–6Al–4V ELI alloy, in martensitic and two-phase (α
+
β) microstructural conditions, was studied in a Ringer’s solution. The wear experiments were performed at room temperature with a normal load of 40
N and sliding speeds 0.26, 0.5 and 1.0
m/s. The corrosion behaviour was studied at 37
°C using open circuit potential-time measurements and potentiodynamic polarization. It was found that Ti–13Nb–13Zr alloy has a substantially lower wear resistance than Ti–6Al–4V ELI alloy in both microstructural conditions. Surface damage extent increases with sliding speed increase and is always smallest for martensitic Ti–6Al–4V ELI alloy with highest hardness. Both alloys exhibit spontaneous passivity in Ringer’s solution. Corrosion potential values are similar for all three materials. However, Ti–13Nb–13Zr and martensitic Ti–6Al–4V ELI alloys show improved corrosion resistance comparatively to Ti–6Al–4V ELI alloy with (α
+
β) microstructure. Martensitic Ti–6Al–4V ELI alloy possesses the best combination of both corrosion and wear resistance, although its corrosion resistance is found to be slightly higher than that of the Ti–13Nb–13Zr alloy.</description><subject>A. Ringer’s solution</subject><subject>A. Ti orthopaedic alloys</subject><subject>Abrasion resistance</subject><subject>Abrasion resistant alloys</subject><subject>Alloys</subject><subject>Applied sciences</subject><subject>C. Corrosion resistance</subject><subject>C. Microstructures</subject><subject>C. Wear rate</subject><subject>Contact of materials. Friction. Wear</subject><subject>Corrosion</subject><subject>Corrosion environments</subject><subject>Corrosive wear</subject><subject>Exact sciences and technology</subject><subject>Mechanical properties and methods of testing. Rheology. Fracture mechanics. Tribology</subject><subject>Metals. Metallurgy</subject><subject>Microstructure</subject><subject>Titanium base alloys</subject><subject>Wear resistance</subject><issn>0010-938X</issn><issn>1879-0496</issn><fulltext>true</fulltext><rsrctype>article</rsrctype><creationdate>2011</creationdate><recordtype>article</recordtype><recordid>eNp9kc9O3DAQxq2qlbqlfQMOvqByyXYce53kUgkh_lRCcKF_xMVy7Al45Y0XO0HaG-_AG_IkdQjiyMUjjX_zjeb7CNlnsGTA5I_10oSYjFuWMLXYEpj4QBasrpoCRCM_kgXkn6Lh9b_P5EtKawCY2AXZ_EUdqe4tzRIxJBd62uKdfnBhjDR09No9Pz4xftm-lJuZfWnKI59f8Ydq78MuUdfT5Daj1wNaur3bZS0fbp3RnqbgxyFLfyWfOu0Tfnute-T36cn18XlxcXX26_joojAC2FDYioMVnK_4qgW2wg6lsUJiDRZaI1uNupMtVl3Z1BXH0mrelmi0sbbCTnK-R77PutsY7kdMg9q4ZNB73WMYk6qlEFBXMJGH75JMVkxk35oqo2JGTfYpRezUNrqNjjvFQE05qLWac1CTt4oxlXPIYwevG3TKXnRR98alt9mS52NZIzP3c-YwG_PgMKqshL1B6yKaQdng3l_0H0ZRpKg</recordid><startdate>20110201</startdate><enddate>20110201</enddate><creator>Cvijović-Alagić, I.</creator><creator>Cvijović, Z.</creator><creator>Mitrović, S.</creator><creator>Panić, V.</creator><creator>Rakin, M.</creator><general>Elsevier Ltd</general><general>Elsevier</general><scope>IQODW</scope><scope>AAYXX</scope><scope>CITATION</scope><scope>7SE</scope><scope>8BQ</scope><scope>8FD</scope><scope>F28</scope><scope>FR3</scope><scope>JG9</scope></search><sort><creationdate>20110201</creationdate><title>Wear and corrosion behaviour of Ti–13Nb–13Zr and Ti–6Al–4V alloys in simulated physiological solution</title><author>Cvijović-Alagić, I. ; Cvijović, Z. ; Mitrović, S. ; Panić, V. ; Rakin, M.</author></sort><facets><frbrtype>5</frbrtype><frbrgroupid>cdi_FETCH-LOGICAL-c401t-d730d433535b015efe6cd46e80d0bc6baeaf6be7f29873e2da3b2ecacdd7ef633</frbrgroupid><rsrctype>articles</rsrctype><prefilter>articles</prefilter><language>eng</language><creationdate>2011</creationdate><topic>A. Ringer’s solution</topic><topic>A. Ti orthopaedic alloys</topic><topic>Abrasion resistance</topic><topic>Abrasion resistant alloys</topic><topic>Alloys</topic><topic>Applied sciences</topic><topic>C. Corrosion resistance</topic><topic>C. Microstructures</topic><topic>C. Wear rate</topic><topic>Contact of materials. Friction. Wear</topic><topic>Corrosion</topic><topic>Corrosion environments</topic><topic>Corrosive wear</topic><topic>Exact sciences and technology</topic><topic>Mechanical properties and methods of testing. Rheology. Fracture mechanics. Tribology</topic><topic>Metals. Metallurgy</topic><topic>Microstructure</topic><topic>Titanium base alloys</topic><topic>Wear resistance</topic><toplevel>peer_reviewed</toplevel><toplevel>online_resources</toplevel><creatorcontrib>Cvijović-Alagić, I.</creatorcontrib><creatorcontrib>Cvijović, Z.</creatorcontrib><creatorcontrib>Mitrović, S.</creatorcontrib><creatorcontrib>Panić, V.</creatorcontrib><creatorcontrib>Rakin, M.</creatorcontrib><collection>Pascal-Francis</collection><collection>CrossRef</collection><collection>Corrosion Abstracts</collection><collection>METADEX</collection><collection>Technology Research Database</collection><collection>ANTE: Abstracts in New Technology & Engineering</collection><collection>Engineering Research Database</collection><collection>Materials Research Database</collection><jtitle>Corrosion science</jtitle></facets><delivery><delcategory>Remote Search Resource</delcategory><fulltext>fulltext</fulltext></delivery><addata><au>Cvijović-Alagić, I.</au><au>Cvijović, Z.</au><au>Mitrović, S.</au><au>Panić, V.</au><au>Rakin, M.</au><format>journal</format><genre>article</genre><ristype>JOUR</ristype><atitle>Wear and corrosion behaviour of Ti–13Nb–13Zr and Ti–6Al–4V alloys in simulated physiological solution</atitle><jtitle>Corrosion science</jtitle><date>2011-02-01</date><risdate>2011</risdate><volume>53</volume><issue>2</issue><spage>796</spage><epage>808</epage><pages>796-808</pages><issn>0010-938X</issn><eissn>1879-0496</eissn><coden>CRRSAA</coden><abstract>► Ti–13Nb–13Zr wear resistance is substantially lower than that of Ti–6Al–4V alloy. ► Wear of both alloys occurs by adhesion and abrasion, which operate simultaneously. ► Both alloys exhibit spontaneous passivity in Ringer’s solution at 37
°C. ► Corrosion resistance of martensitic Ti–6Al–4V and Ti–13Nb–13Zr alloys are very similar and improved in comparison to the two-phase (α
+
β) Ti–6Al–4V alloy. ► Ti–6Al–4V alloy with martensitic microstructure displays the best combination of both corrosion and wear resistance.
Wear and corrosion behaviour of cold-rolled Ti–13Nb–13Zr alloy, with martensitic microstructure, and Ti–6Al–4V ELI alloy, in martensitic and two-phase (α
+
β) microstructural conditions, was studied in a Ringer’s solution. The wear experiments were performed at room temperature with a normal load of 40
N and sliding speeds 0.26, 0.5 and 1.0
m/s. The corrosion behaviour was studied at 37
°C using open circuit potential-time measurements and potentiodynamic polarization. It was found that Ti–13Nb–13Zr alloy has a substantially lower wear resistance than Ti–6Al–4V ELI alloy in both microstructural conditions. Surface damage extent increases with sliding speed increase and is always smallest for martensitic Ti–6Al–4V ELI alloy with highest hardness. Both alloys exhibit spontaneous passivity in Ringer’s solution. Corrosion potential values are similar for all three materials. However, Ti–13Nb–13Zr and martensitic Ti–6Al–4V ELI alloys show improved corrosion resistance comparatively to Ti–6Al–4V ELI alloy with (α
+
β) microstructure. Martensitic Ti–6Al–4V ELI alloy possesses the best combination of both corrosion and wear resistance, although its corrosion resistance is found to be slightly higher than that of the Ti–13Nb–13Zr alloy.</abstract><cop>Kidlington</cop><pub>Elsevier Ltd</pub><doi>10.1016/j.corsci.2010.11.014</doi><tpages>13</tpages></addata></record> |
| fulltext | fulltext |
| identifier | ISSN: 0010-938X |
| ispartof | Corrosion science, 2011-02, Vol.53 (2), p.796-808 |
| issn | 0010-938X 1879-0496 |
| language | eng |
| recordid | cdi_proquest_miscellaneous_864408703 |
| source | Elsevier ScienceDirect Journals |
| subjects | A. Ringer’s solution A. Ti orthopaedic alloys Abrasion resistance Abrasion resistant alloys Alloys Applied sciences C. Corrosion resistance C. Microstructures C. Wear rate Contact of materials. Friction. Wear Corrosion Corrosion environments Corrosive wear Exact sciences and technology Mechanical properties and methods of testing. Rheology. Fracture mechanics. Tribology Metals. Metallurgy Microstructure Titanium base alloys Wear resistance |
| title | Wear and corrosion behaviour of Ti–13Nb–13Zr and Ti–6Al–4V alloys in simulated physiological solution |
| url | https://sfx.bib-bvb.de/sfx_tum?ctx_ver=Z39.88-2004&ctx_enc=info:ofi/enc:UTF-8&ctx_tim=2025-02-05T06%3A54%3A33IST&url_ver=Z39.88-2004&url_ctx_fmt=infofi/fmt:kev:mtx:ctx&rfr_id=info:sid/primo.exlibrisgroup.com:primo3-Article-proquest_cross&rft_val_fmt=info:ofi/fmt:kev:mtx:journal&rft.genre=article&rft.atitle=Wear%20and%20corrosion%20behaviour%20of%20Ti%E2%80%9313Nb%E2%80%9313Zr%20and%20Ti%E2%80%936Al%E2%80%934V%20alloys%20in%20simulated%20physiological%20solution&rft.jtitle=Corrosion%20science&rft.au=Cvijovi%C4%87-Alagi%C4%87,%20I.&rft.date=2011-02-01&rft.volume=53&rft.issue=2&rft.spage=796&rft.epage=808&rft.pages=796-808&rft.issn=0010-938X&rft.eissn=1879-0496&rft.coden=CRRSAA&rft_id=info:doi/10.1016/j.corsci.2010.11.014&rft_dat=%3Cproquest_cross%3E1671493897%3C/proquest_cross%3E%3Curl%3E%3C/url%3E&disable_directlink=true&sfx.directlink=off&sfx.report_link=0&rft_id=info:oai/&rft_pqid=1671493897&rft_id=info:pmid/&rft_els_id=S0010938X10005597&rfr_iscdi=true |