Friction stir welding joints of 2195-T8 Al–Li alloys: Correlation of temperature evolution, microstructure and mechanical properties
7.5 mm thick 2195-T8 Al–Li alloy plates were manufactured by friction stir welding (FSW). Thermal history of different regions in welding joints was recorded during welding. Microstructure characterization was conducted out by electron back scattered diffraction (EBSD), X-ray diffraction (XRD) and t...
Gespeichert in:
| Veröffentlicht in: | Materials science & engineering. A, Structural materials : properties, microstructure and processing Structural materials : properties, microstructure and processing, 2021-08, Vol.823, p.141501, Article 141501 |
|---|---|
| Hauptverfasser: | , , , , , , , , |
| Format: | Artikel |
| Sprache: | eng |
| Schlagworte: | |
| Online-Zugang: | Volltext |
| Tags: |
Tag hinzufügen
Keine Tags, Fügen Sie den ersten Tag hinzu!
|
| container_end_page | |
|---|---|
| container_issue | |
| container_start_page | 141501 |
| container_title | Materials science & engineering. A, Structural materials : properties, microstructure and processing |
| container_volume | 823 |
| creator | Peng, Chen Jing, Chen Siyi, Qin Siqi, Zou Shoubo, Song Ting, Jiang Zhiqing, Zhang Zhihong, Jia Qing, Liu |
| description | 7.5 mm thick 2195-T8 Al–Li alloy plates were manufactured by friction stir welding (FSW). Thermal history of different regions in welding joints was recorded during welding. Microstructure characterization was conducted out by electron back scattered diffraction (EBSD), X-ray diffraction (XRD) and transmission electron microscopy (TEM). Mechanical properties were measured using micro-hardness and tensile test. The correlation of temperature evolution, microstructure and mechanical properties of individual regions in welding joints was discussed. It was shown that peak temperature was 358 °C–376 °C in the heat affected zone (HAZ) where joint failure occurred due to the dissolution and coarsening of T1 and development of coarse grain boundary phase and precipitate free zones (PFZs). Peak temperature of thermo-mechanically affected zone (TMAZ) ranged from 376 °C to 401 °C, leading to complicated precipitation behavior. The dissolution and coarsening of precipitates resulted in joint softening, while a layer of fine equiaxed grains at the interface of the AS-TMAZ/NZ increased the hardness of this region. The base material (BM) mainly consisted of rolling textures, while the NZ and TMAZ had strong shear textures. Moreover, the intensity of shear textures was evidently higher in the NZ, but relatively lower in the RS-TMAZ. The hardness and tensile strength profiles of welding joints appeared in “W” shape. From the base material zone to the nugget zone within a welding joint, fracture mechanism changed from brittleness fracture to toughness fracture.
•Microstructural features and mechanical properties of 2195 aluminum alloy friction stir welding (FSW) joints were studied in detail.•The correlation of temperature evolution, microstructure and mechanical properties of different regions of welding joints was discussed.•The evolution of fracture mechanism in different regions of FSW joints was studied. |
| doi_str_mv | 10.1016/j.msea.2021.141501 |
| format | Article |
| fullrecord | <record><control><sourceid>proquest_cross</sourceid><recordid>TN_cdi_proquest_journals_2575539669</recordid><sourceformat>XML</sourceformat><sourcesystem>PC</sourcesystem><els_id>S092150932100770X</els_id><sourcerecordid>2575539669</sourcerecordid><originalsourceid>FETCH-LOGICAL-c377t-e693e6c5143e10953e51c1023d087a2eb3d4d15837a8bfe7c695faea274664dd3</originalsourceid><addsrcrecordid>eNp9kL1O5DAUhS0EEsPAC1BZoiWzvnacH0SDRgu70kg0UFvGvgFHSTzYDoiOal-AN-RJSJitqW5xznfP0SHkFNgKGBS_2lUfUa8447CCHCSDPbKAqhRZXotinyxYzSGTrBaH5CjGljEGOZML8u86OJOcH2hMLtBX7KwbHmnr3ZAi9Q3lUMvsrqJX3ef7x8ZR3XX-LV7QtQ8BO_2NTraE_RaDTmNAii--G2fhnPbOBB9TGM23ogdLezRPenBGd3Qb_AQlh_GYHDS6i3jy_y7J_fXvu_WfbHN783d9tcmMKMuUYVELLIyEXCCwWgqUYIBxYVlVao4PwuYWZCVKXT00WJqilo1Gzcu8KHJrxZKc7f5O0c8jxqRaP4ZhilRcllKKupgiloTvXHP5GLBR2-B6Hd4UMDXvrVo1763mvdVu7wm63EE49X9xGFQ0DgeD1gU0SVnvfsK_AKnoi1k</addsrcrecordid><sourcetype>Aggregation Database</sourcetype><iscdi>true</iscdi><recordtype>article</recordtype><pqid>2575539669</pqid></control><display><type>article</type><title>Friction stir welding joints of 2195-T8 Al–Li alloys: Correlation of temperature evolution, microstructure and mechanical properties</title><source>Elsevier ScienceDirect Journals</source><creator>Peng, Chen ; Jing, Chen ; Siyi, Qin ; Siqi, Zou ; Shoubo, Song ; Ting, Jiang ; Zhiqing, Zhang ; Zhihong, Jia ; Qing, Liu</creator><creatorcontrib>Peng, Chen ; Jing, Chen ; Siyi, Qin ; Siqi, Zou ; Shoubo, Song ; Ting, Jiang ; Zhiqing, Zhang ; Zhihong, Jia ; Qing, Liu</creatorcontrib><description>7.5 mm thick 2195-T8 Al–Li alloy plates were manufactured by friction stir welding (FSW). Thermal history of different regions in welding joints was recorded during welding. Microstructure characterization was conducted out by electron back scattered diffraction (EBSD), X-ray diffraction (XRD) and transmission electron microscopy (TEM). Mechanical properties were measured using micro-hardness and tensile test. The correlation of temperature evolution, microstructure and mechanical properties of individual regions in welding joints was discussed. It was shown that peak temperature was 358 °C–376 °C in the heat affected zone (HAZ) where joint failure occurred due to the dissolution and coarsening of T1 and development of coarse grain boundary phase and precipitate free zones (PFZs). Peak temperature of thermo-mechanically affected zone (TMAZ) ranged from 376 °C to 401 °C, leading to complicated precipitation behavior. The dissolution and coarsening of precipitates resulted in joint softening, while a layer of fine equiaxed grains at the interface of the AS-TMAZ/NZ increased the hardness of this region. The base material (BM) mainly consisted of rolling textures, while the NZ and TMAZ had strong shear textures. Moreover, the intensity of shear textures was evidently higher in the NZ, but relatively lower in the RS-TMAZ. The hardness and tensile strength profiles of welding joints appeared in “W” shape. From the base material zone to the nugget zone within a welding joint, fracture mechanism changed from brittleness fracture to toughness fracture.
•Microstructural features and mechanical properties of 2195 aluminum alloy friction stir welding (FSW) joints were studied in detail.•The correlation of temperature evolution, microstructure and mechanical properties of different regions of welding joints was discussed.•The evolution of fracture mechanism in different regions of FSW joints was studied.</description><identifier>ISSN: 0921-5093</identifier><identifier>EISSN: 1873-4936</identifier><identifier>DOI: 10.1016/j.msea.2021.141501</identifier><language>eng</language><publisher>Lausanne: Elsevier B.V</publisher><subject>2195-T8 Al–Li alloys ; Aluminum-lithium alloys ; Coarsening ; Dissolution ; Evolution ; Fracture mechanics ; Fracture toughness ; Friction stir welding ; Grain boundaries ; Heat affected zone ; Heat treating ; Mechanical properties ; Metal plates ; Microhardness ; Microstructure ; Precipitates ; Temperature ; Temperature evolution ; Tensile strength ; Tensile tests ; Texture ; Welded joints</subject><ispartof>Materials science & engineering. A, Structural materials : properties, microstructure and processing, 2021-08, Vol.823, p.141501, Article 141501</ispartof><rights>2021</rights><rights>Copyright Elsevier BV Aug 17, 2021</rights><lds50>peer_reviewed</lds50><woscitedreferencessubscribed>false</woscitedreferencessubscribed><citedby>FETCH-LOGICAL-c377t-e693e6c5143e10953e51c1023d087a2eb3d4d15837a8bfe7c695faea274664dd3</citedby><cites>FETCH-LOGICAL-c377t-e693e6c5143e10953e51c1023d087a2eb3d4d15837a8bfe7c695faea274664dd3</cites></display><links><openurl>$$Topenurl_article</openurl><openurlfulltext>$$Topenurlfull_article</openurlfulltext><thumbnail>$$Tsyndetics_thumb_exl</thumbnail><linktohtml>$$Uhttps://www.sciencedirect.com/science/article/pii/S092150932100770X$$EHTML$$P50$$Gelsevier$$H</linktohtml><link.rule.ids>314,776,780,3536,27902,27903,65308</link.rule.ids></links><search><creatorcontrib>Peng, Chen</creatorcontrib><creatorcontrib>Jing, Chen</creatorcontrib><creatorcontrib>Siyi, Qin</creatorcontrib><creatorcontrib>Siqi, Zou</creatorcontrib><creatorcontrib>Shoubo, Song</creatorcontrib><creatorcontrib>Ting, Jiang</creatorcontrib><creatorcontrib>Zhiqing, Zhang</creatorcontrib><creatorcontrib>Zhihong, Jia</creatorcontrib><creatorcontrib>Qing, Liu</creatorcontrib><title>Friction stir welding joints of 2195-T8 Al–Li alloys: Correlation of temperature evolution, microstructure and mechanical properties</title><title>Materials science & engineering. A, Structural materials : properties, microstructure and processing</title><description>7.5 mm thick 2195-T8 Al–Li alloy plates were manufactured by friction stir welding (FSW). Thermal history of different regions in welding joints was recorded during welding. Microstructure characterization was conducted out by electron back scattered diffraction (EBSD), X-ray diffraction (XRD) and transmission electron microscopy (TEM). Mechanical properties were measured using micro-hardness and tensile test. The correlation of temperature evolution, microstructure and mechanical properties of individual regions in welding joints was discussed. It was shown that peak temperature was 358 °C–376 °C in the heat affected zone (HAZ) where joint failure occurred due to the dissolution and coarsening of T1 and development of coarse grain boundary phase and precipitate free zones (PFZs). Peak temperature of thermo-mechanically affected zone (TMAZ) ranged from 376 °C to 401 °C, leading to complicated precipitation behavior. The dissolution and coarsening of precipitates resulted in joint softening, while a layer of fine equiaxed grains at the interface of the AS-TMAZ/NZ increased the hardness of this region. The base material (BM) mainly consisted of rolling textures, while the NZ and TMAZ had strong shear textures. Moreover, the intensity of shear textures was evidently higher in the NZ, but relatively lower in the RS-TMAZ. The hardness and tensile strength profiles of welding joints appeared in “W” shape. From the base material zone to the nugget zone within a welding joint, fracture mechanism changed from brittleness fracture to toughness fracture.
•Microstructural features and mechanical properties of 2195 aluminum alloy friction stir welding (FSW) joints were studied in detail.•The correlation of temperature evolution, microstructure and mechanical properties of different regions of welding joints was discussed.•The evolution of fracture mechanism in different regions of FSW joints was studied.</description><subject>2195-T8 Al–Li alloys</subject><subject>Aluminum-lithium alloys</subject><subject>Coarsening</subject><subject>Dissolution</subject><subject>Evolution</subject><subject>Fracture mechanics</subject><subject>Fracture toughness</subject><subject>Friction stir welding</subject><subject>Grain boundaries</subject><subject>Heat affected zone</subject><subject>Heat treating</subject><subject>Mechanical properties</subject><subject>Metal plates</subject><subject>Microhardness</subject><subject>Microstructure</subject><subject>Precipitates</subject><subject>Temperature</subject><subject>Temperature evolution</subject><subject>Tensile strength</subject><subject>Tensile tests</subject><subject>Texture</subject><subject>Welded joints</subject><issn>0921-5093</issn><issn>1873-4936</issn><fulltext>true</fulltext><rsrctype>article</rsrctype><creationdate>2021</creationdate><recordtype>article</recordtype><recordid>eNp9kL1O5DAUhS0EEsPAC1BZoiWzvnacH0SDRgu70kg0UFvGvgFHSTzYDoiOal-AN-RJSJitqW5xznfP0SHkFNgKGBS_2lUfUa8447CCHCSDPbKAqhRZXotinyxYzSGTrBaH5CjGljEGOZML8u86OJOcH2hMLtBX7KwbHmnr3ZAi9Q3lUMvsrqJX3ef7x8ZR3XX-LV7QtQ8BO_2NTraE_RaDTmNAii--G2fhnPbOBB9TGM23ogdLezRPenBGd3Qb_AQlh_GYHDS6i3jy_y7J_fXvu_WfbHN783d9tcmMKMuUYVELLIyEXCCwWgqUYIBxYVlVao4PwuYWZCVKXT00WJqilo1Gzcu8KHJrxZKc7f5O0c8jxqRaP4ZhilRcllKKupgiloTvXHP5GLBR2-B6Hd4UMDXvrVo1763mvdVu7wm63EE49X9xGFQ0DgeD1gU0SVnvfsK_AKnoi1k</recordid><startdate>20210817</startdate><enddate>20210817</enddate><creator>Peng, Chen</creator><creator>Jing, Chen</creator><creator>Siyi, Qin</creator><creator>Siqi, Zou</creator><creator>Shoubo, Song</creator><creator>Ting, Jiang</creator><creator>Zhiqing, Zhang</creator><creator>Zhihong, Jia</creator><creator>Qing, Liu</creator><general>Elsevier B.V</general><general>Elsevier BV</general><scope>AAYXX</scope><scope>CITATION</scope><scope>7SR</scope><scope>8BQ</scope><scope>8FD</scope><scope>JG9</scope></search><sort><creationdate>20210817</creationdate><title>Friction stir welding joints of 2195-T8 Al–Li alloys: Correlation of temperature evolution, microstructure and mechanical properties</title><author>Peng, Chen ; Jing, Chen ; Siyi, Qin ; Siqi, Zou ; Shoubo, Song ; Ting, Jiang ; Zhiqing, Zhang ; Zhihong, Jia ; Qing, Liu</author></sort><facets><frbrtype>5</frbrtype><frbrgroupid>cdi_FETCH-LOGICAL-c377t-e693e6c5143e10953e51c1023d087a2eb3d4d15837a8bfe7c695faea274664dd3</frbrgroupid><rsrctype>articles</rsrctype><prefilter>articles</prefilter><language>eng</language><creationdate>2021</creationdate><topic>2195-T8 Al–Li alloys</topic><topic>Aluminum-lithium alloys</topic><topic>Coarsening</topic><topic>Dissolution</topic><topic>Evolution</topic><topic>Fracture mechanics</topic><topic>Fracture toughness</topic><topic>Friction stir welding</topic><topic>Grain boundaries</topic><topic>Heat affected zone</topic><topic>Heat treating</topic><topic>Mechanical properties</topic><topic>Metal plates</topic><topic>Microhardness</topic><topic>Microstructure</topic><topic>Precipitates</topic><topic>Temperature</topic><topic>Temperature evolution</topic><topic>Tensile strength</topic><topic>Tensile tests</topic><topic>Texture</topic><topic>Welded joints</topic><toplevel>peer_reviewed</toplevel><toplevel>online_resources</toplevel><creatorcontrib>Peng, Chen</creatorcontrib><creatorcontrib>Jing, Chen</creatorcontrib><creatorcontrib>Siyi, Qin</creatorcontrib><creatorcontrib>Siqi, Zou</creatorcontrib><creatorcontrib>Shoubo, Song</creatorcontrib><creatorcontrib>Ting, Jiang</creatorcontrib><creatorcontrib>Zhiqing, Zhang</creatorcontrib><creatorcontrib>Zhihong, Jia</creatorcontrib><creatorcontrib>Qing, Liu</creatorcontrib><collection>CrossRef</collection><collection>Engineered Materials Abstracts</collection><collection>METADEX</collection><collection>Technology Research Database</collection><collection>Materials Research Database</collection><jtitle>Materials science & engineering. A, Structural materials : properties, microstructure and processing</jtitle></facets><delivery><delcategory>Remote Search Resource</delcategory><fulltext>fulltext</fulltext></delivery><addata><au>Peng, Chen</au><au>Jing, Chen</au><au>Siyi, Qin</au><au>Siqi, Zou</au><au>Shoubo, Song</au><au>Ting, Jiang</au><au>Zhiqing, Zhang</au><au>Zhihong, Jia</au><au>Qing, Liu</au><format>journal</format><genre>article</genre><ristype>JOUR</ristype><atitle>Friction stir welding joints of 2195-T8 Al–Li alloys: Correlation of temperature evolution, microstructure and mechanical properties</atitle><jtitle>Materials science & engineering. A, Structural materials : properties, microstructure and processing</jtitle><date>2021-08-17</date><risdate>2021</risdate><volume>823</volume><spage>141501</spage><pages>141501-</pages><artnum>141501</artnum><issn>0921-5093</issn><eissn>1873-4936</eissn><abstract>7.5 mm thick 2195-T8 Al–Li alloy plates were manufactured by friction stir welding (FSW). Thermal history of different regions in welding joints was recorded during welding. Microstructure characterization was conducted out by electron back scattered diffraction (EBSD), X-ray diffraction (XRD) and transmission electron microscopy (TEM). Mechanical properties were measured using micro-hardness and tensile test. The correlation of temperature evolution, microstructure and mechanical properties of individual regions in welding joints was discussed. It was shown that peak temperature was 358 °C–376 °C in the heat affected zone (HAZ) where joint failure occurred due to the dissolution and coarsening of T1 and development of coarse grain boundary phase and precipitate free zones (PFZs). Peak temperature of thermo-mechanically affected zone (TMAZ) ranged from 376 °C to 401 °C, leading to complicated precipitation behavior. The dissolution and coarsening of precipitates resulted in joint softening, while a layer of fine equiaxed grains at the interface of the AS-TMAZ/NZ increased the hardness of this region. The base material (BM) mainly consisted of rolling textures, while the NZ and TMAZ had strong shear textures. Moreover, the intensity of shear textures was evidently higher in the NZ, but relatively lower in the RS-TMAZ. The hardness and tensile strength profiles of welding joints appeared in “W” shape. From the base material zone to the nugget zone within a welding joint, fracture mechanism changed from brittleness fracture to toughness fracture.
•Microstructural features and mechanical properties of 2195 aluminum alloy friction stir welding (FSW) joints were studied in detail.•The correlation of temperature evolution, microstructure and mechanical properties of different regions of welding joints was discussed.•The evolution of fracture mechanism in different regions of FSW joints was studied.</abstract><cop>Lausanne</cop><pub>Elsevier B.V</pub><doi>10.1016/j.msea.2021.141501</doi></addata></record> |
| fulltext | fulltext |
| identifier | ISSN: 0921-5093 |
| ispartof | Materials science & engineering. A, Structural materials : properties, microstructure and processing, 2021-08, Vol.823, p.141501, Article 141501 |
| issn | 0921-5093 1873-4936 |
| language | eng |
| recordid | cdi_proquest_journals_2575539669 |
| source | Elsevier ScienceDirect Journals |
| subjects | 2195-T8 Al–Li alloys Aluminum-lithium alloys Coarsening Dissolution Evolution Fracture mechanics Fracture toughness Friction stir welding Grain boundaries Heat affected zone Heat treating Mechanical properties Metal plates Microhardness Microstructure Precipitates Temperature Temperature evolution Tensile strength Tensile tests Texture Welded joints |
| title | Friction stir welding joints of 2195-T8 Al–Li alloys: Correlation of temperature evolution, microstructure and mechanical properties |
| url | https://sfx.bib-bvb.de/sfx_tum?ctx_ver=Z39.88-2004&ctx_enc=info:ofi/enc:UTF-8&ctx_tim=2025-01-27T09%3A47%3A12IST&url_ver=Z39.88-2004&url_ctx_fmt=infofi/fmt:kev:mtx:ctx&rfr_id=info:sid/primo.exlibrisgroup.com:primo3-Article-proquest_cross&rft_val_fmt=info:ofi/fmt:kev:mtx:journal&rft.genre=article&rft.atitle=Friction%20stir%20welding%20joints%20of%202195-T8%20Al%E2%80%93Li%20alloys:%20Correlation%20of%20temperature%20evolution,%20microstructure%20and%20mechanical%20properties&rft.jtitle=Materials%20science%20&%20engineering.%20A,%20Structural%20materials%20:%20properties,%20microstructure%20and%20processing&rft.au=Peng,%20Chen&rft.date=2021-08-17&rft.volume=823&rft.spage=141501&rft.pages=141501-&rft.artnum=141501&rft.issn=0921-5093&rft.eissn=1873-4936&rft_id=info:doi/10.1016/j.msea.2021.141501&rft_dat=%3Cproquest_cross%3E2575539669%3C/proquest_cross%3E%3Curl%3E%3C/url%3E&disable_directlink=true&sfx.directlink=off&sfx.report_link=0&rft_id=info:oai/&rft_pqid=2575539669&rft_id=info:pmid/&rft_els_id=S092150932100770X&rfr_iscdi=true |