Finishing of Hob Tooth Flank by Plunge Grinding
It is desirable to increase the number of cutting edges per bob revolution as much as possible to reduce the burden of each cutting edge and the polygon error caused in bobbing process. But, it is difficult to increase the number of cutting edges because interference between the grinding wheel and t...
Gespeichert in:
| Veröffentlicht in: | Journal of the Japan Society for Precision Engineering 2003/11/05, Vol.69(11), pp.1615-1619 |
|---|---|
| Hauptverfasser: | , , |
| Format: | Artikel |
| Sprache: | jpn |
| Schlagworte: | |
| Online-Zugang: | Volltext |
| Tags: |
Tag hinzufügen
Keine Tags, Fügen Sie den ersten Tag hinzu!
|
| container_end_page | 1619 |
|---|---|
| container_issue | 11 |
| container_start_page | 1615 |
| container_title | Journal of the Japan Society for Precision Engineering |
| container_volume | 69 |
| creator | ONO, Takayoshi YOSHINO, Hidehiro OHSHIMA, Fumihiro |
| description | It is desirable to increase the number of cutting edges per bob revolution as much as possible to reduce the burden of each cutting edge and the polygon error caused in bobbing process. But, it is difficult to increase the number of cutting edges because interference between the grinding wheel and the following cutting edge in relief grinding of the hob is apt to occur. A method for finishing the hob cutting edges by plunge grinding without relieving motion is proposed. In the method, the cutting edge is finished when the grinding wheel and hob work are in a static position. In this paper, the calculation method of the grinding wheel profile to finish the cutting edges, the optimum static position to obtain the desirable clearance angle, and the effects of the positioning errors of the grinding wheel on the accuracy of finished cutting edges are investigated. |
| doi_str_mv | 10.2493/jjspe.69.1615 |
| format | Article |
| fullrecord | <record><control><sourceid>jstage_cross</sourceid><recordid>TN_cdi_crossref_primary_10_2493_jjspe_69_1615</recordid><sourceformat>XML</sourceformat><sourcesystem>PC</sourcesystem><sourcerecordid>article_jjspe1986_69_11_69_11_1615_article_char_en</sourcerecordid><originalsourceid>FETCH-LOGICAL-c2695-120e1d68536b1a7bdd1d70c906b3a966fc51015cb0e6f6d18ca40e6d7c688a773</originalsourceid><addsrcrecordid>eNo9z01rAjEQBuBQWqhYj73nD6xmsu4kORapbkGwBwu9hXytxm53JbEH_339wsvMHJ534CXkFdiYT1U52e3yPoxRjQGheiADkJIXKKrvRzJgCnjBuFTPZJRztIxxFIyXfEAm89jFvI3dhvYNrXtL131_2NJ5a7ofao_0s_3rNoEuUuz8Sb2Qp8a0OYxue0i-5u_rWV0sV4uP2duycBxVVQBnATzKqkQLRljvwQvmFENbGoXYuAoYVM6ygA16kM5MT6cXDqU0QpRDUlz_utTnnEKj9yn-mnTUwPS5sL4U1qj0ufDJ11e_ywezCXdt0iG6Nlw1KImXBNzmOXonbmuSDl35D3gJYck</addsrcrecordid><sourcetype>Aggregation Database</sourcetype><iscdi>true</iscdi><recordtype>article</recordtype></control><display><type>article</type><title>Finishing of Hob Tooth Flank by Plunge Grinding</title><source>EZB-FREE-00999 freely available EZB journals</source><creator>ONO, Takayoshi ; YOSHINO, Hidehiro ; OHSHIMA, Fumihiro</creator><creatorcontrib>ONO, Takayoshi ; YOSHINO, Hidehiro ; OHSHIMA, Fumihiro</creatorcontrib><description>It is desirable to increase the number of cutting edges per bob revolution as much as possible to reduce the burden of each cutting edge and the polygon error caused in bobbing process. But, it is difficult to increase the number of cutting edges because interference between the grinding wheel and the following cutting edge in relief grinding of the hob is apt to occur. A method for finishing the hob cutting edges by plunge grinding without relieving motion is proposed. In the method, the cutting edge is finished when the grinding wheel and hob work are in a static position. In this paper, the calculation method of the grinding wheel profile to finish the cutting edges, the optimum static position to obtain the desirable clearance angle, and the effects of the positioning errors of the grinding wheel on the accuracy of finished cutting edges are investigated.</description><identifier>ISSN: 0912-0289</identifier><identifier>EISSN: 1882-675X</identifier><identifier>DOI: 10.2493/jjspe.69.1615</identifier><language>jpn</language><publisher>The Japan Society for Precision Engineering</publisher><subject>clearance angle ; cutting edge ; gash number ; hob ; plunge grinding ; profile error ; profiled grinding wheel ; relief grinding ; tooth flank</subject><ispartof>Journal of the Japan Society for Precision Engineering, 2003/11/05, Vol.69(11), pp.1615-1619</ispartof><rights>by The Japan Society for Precision Engineering</rights><oa>free_for_read</oa><woscitedreferencessubscribed>false</woscitedreferencessubscribed></display><links><openurl>$$Topenurl_article</openurl><openurlfulltext>$$Topenurlfull_article</openurlfulltext><thumbnail>$$Tsyndetics_thumb_exl</thumbnail><link.rule.ids>314,777,781,4010,27904,27905,27906</link.rule.ids></links><search><creatorcontrib>ONO, Takayoshi</creatorcontrib><creatorcontrib>YOSHINO, Hidehiro</creatorcontrib><creatorcontrib>OHSHIMA, Fumihiro</creatorcontrib><title>Finishing of Hob Tooth Flank by Plunge Grinding</title><title>Journal of the Japan Society for Precision Engineering</title><addtitle>Journal of the Japan Society for Precision Engineering</addtitle><description>It is desirable to increase the number of cutting edges per bob revolution as much as possible to reduce the burden of each cutting edge and the polygon error caused in bobbing process. But, it is difficult to increase the number of cutting edges because interference between the grinding wheel and the following cutting edge in relief grinding of the hob is apt to occur. A method for finishing the hob cutting edges by plunge grinding without relieving motion is proposed. In the method, the cutting edge is finished when the grinding wheel and hob work are in a static position. In this paper, the calculation method of the grinding wheel profile to finish the cutting edges, the optimum static position to obtain the desirable clearance angle, and the effects of the positioning errors of the grinding wheel on the accuracy of finished cutting edges are investigated.</description><subject>clearance angle</subject><subject>cutting edge</subject><subject>gash number</subject><subject>hob</subject><subject>plunge grinding</subject><subject>profile error</subject><subject>profiled grinding wheel</subject><subject>relief grinding</subject><subject>tooth flank</subject><issn>0912-0289</issn><issn>1882-675X</issn><fulltext>true</fulltext><rsrctype>article</rsrctype><creationdate>2003</creationdate><recordtype>article</recordtype><recordid>eNo9z01rAjEQBuBQWqhYj73nD6xmsu4kORapbkGwBwu9hXytxm53JbEH_339wsvMHJ534CXkFdiYT1U52e3yPoxRjQGheiADkJIXKKrvRzJgCnjBuFTPZJRztIxxFIyXfEAm89jFvI3dhvYNrXtL131_2NJ5a7ofao_0s_3rNoEuUuz8Sb2Qp8a0OYxue0i-5u_rWV0sV4uP2duycBxVVQBnATzKqkQLRljvwQvmFENbGoXYuAoYVM6ygA16kM5MT6cXDqU0QpRDUlz_utTnnEKj9yn-mnTUwPS5sL4U1qj0ufDJ11e_ywezCXdt0iG6Nlw1KImXBNzmOXonbmuSDl35D3gJYck</recordid><startdate>2003</startdate><enddate>2003</enddate><creator>ONO, Takayoshi</creator><creator>YOSHINO, Hidehiro</creator><creator>OHSHIMA, Fumihiro</creator><general>The Japan Society for Precision Engineering</general><scope>AAYXX</scope><scope>CITATION</scope></search><sort><creationdate>2003</creationdate><title>Finishing of Hob Tooth Flank by Plunge Grinding</title><author>ONO, Takayoshi ; YOSHINO, Hidehiro ; OHSHIMA, Fumihiro</author></sort><facets><frbrtype>5</frbrtype><frbrgroupid>cdi_FETCH-LOGICAL-c2695-120e1d68536b1a7bdd1d70c906b3a966fc51015cb0e6f6d18ca40e6d7c688a773</frbrgroupid><rsrctype>articles</rsrctype><prefilter>articles</prefilter><language>jpn</language><creationdate>2003</creationdate><topic>clearance angle</topic><topic>cutting edge</topic><topic>gash number</topic><topic>hob</topic><topic>plunge grinding</topic><topic>profile error</topic><topic>profiled grinding wheel</topic><topic>relief grinding</topic><topic>tooth flank</topic><toplevel>online_resources</toplevel><creatorcontrib>ONO, Takayoshi</creatorcontrib><creatorcontrib>YOSHINO, Hidehiro</creatorcontrib><creatorcontrib>OHSHIMA, Fumihiro</creatorcontrib><collection>CrossRef</collection><jtitle>Journal of the Japan Society for Precision Engineering</jtitle></facets><delivery><delcategory>Remote Search Resource</delcategory><fulltext>fulltext</fulltext></delivery><addata><au>ONO, Takayoshi</au><au>YOSHINO, Hidehiro</au><au>OHSHIMA, Fumihiro</au><format>journal</format><genre>article</genre><ristype>JOUR</ristype><atitle>Finishing of Hob Tooth Flank by Plunge Grinding</atitle><jtitle>Journal of the Japan Society for Precision Engineering</jtitle><addtitle>Journal of the Japan Society for Precision Engineering</addtitle><date>2003</date><risdate>2003</risdate><volume>69</volume><issue>11</issue><spage>1615</spage><epage>1619</epage><pages>1615-1619</pages><issn>0912-0289</issn><eissn>1882-675X</eissn><abstract>It is desirable to increase the number of cutting edges per bob revolution as much as possible to reduce the burden of each cutting edge and the polygon error caused in bobbing process. But, it is difficult to increase the number of cutting edges because interference between the grinding wheel and the following cutting edge in relief grinding of the hob is apt to occur. A method for finishing the hob cutting edges by plunge grinding without relieving motion is proposed. In the method, the cutting edge is finished when the grinding wheel and hob work are in a static position. In this paper, the calculation method of the grinding wheel profile to finish the cutting edges, the optimum static position to obtain the desirable clearance angle, and the effects of the positioning errors of the grinding wheel on the accuracy of finished cutting edges are investigated.</abstract><pub>The Japan Society for Precision Engineering</pub><doi>10.2493/jjspe.69.1615</doi><tpages>5</tpages><oa>free_for_read</oa></addata></record> |
| fulltext | fulltext |
| identifier | ISSN: 0912-0289 |
| ispartof | Journal of the Japan Society for Precision Engineering, 2003/11/05, Vol.69(11), pp.1615-1619 |
| issn | 0912-0289 1882-675X |
| language | jpn |
| recordid | cdi_crossref_primary_10_2493_jjspe_69_1615 |
| source | EZB-FREE-00999 freely available EZB journals |
| subjects | clearance angle cutting edge gash number hob plunge grinding profile error profiled grinding wheel relief grinding tooth flank |
| title | Finishing of Hob Tooth Flank by Plunge Grinding |
| url | https://sfx.bib-bvb.de/sfx_tum?ctx_ver=Z39.88-2004&ctx_enc=info:ofi/enc:UTF-8&ctx_tim=2025-01-19T22%3A47%3A29IST&url_ver=Z39.88-2004&url_ctx_fmt=infofi/fmt:kev:mtx:ctx&rfr_id=info:sid/primo.exlibrisgroup.com:primo3-Article-jstage_cross&rft_val_fmt=info:ofi/fmt:kev:mtx:journal&rft.genre=article&rft.atitle=Finishing%20of%20Hob%20Tooth%20Flank%20by%20Plunge%20Grinding&rft.jtitle=Journal%20of%20the%20Japan%20Society%20for%20Precision%20Engineering&rft.au=ONO,%20Takayoshi&rft.date=2003&rft.volume=69&rft.issue=11&rft.spage=1615&rft.epage=1619&rft.pages=1615-1619&rft.issn=0912-0289&rft.eissn=1882-675X&rft_id=info:doi/10.2493/jjspe.69.1615&rft_dat=%3Cjstage_cross%3Earticle_jjspe1986_69_11_69_11_1615_article_char_en%3C/jstage_cross%3E%3Curl%3E%3C/url%3E&disable_directlink=true&sfx.directlink=off&sfx.report_link=0&rft_id=info:oai/&rft_id=info:pmid/&rfr_iscdi=true |