A Basis for Selecting the Most Appropriate Small Specimen Creep Test Type

Many components in conventional and nuclear power plant, aero-engines, chemical plant etc., operate at temperatures which are high enough for creep to occur. These include plain pipes, pipe bends, branched pipes etc., the manufacture of such components may also require welds to be inserted in them....

Ausführliche Beschreibung

Gespeichert in:
Bibliographische Detailangaben
Veröffentlicht in:Journal of pressure vessel technology 2014-04, Vol.136 (2)
Hauptverfasser: Hyde, T. H, Hyde, C. J, Sun, W
Format: Artikel
Sprache:eng
Online-Zugang:Volltext
Tags: Tag hinzufügen
Keine Tags, Fügen Sie den ersten Tag hinzu!
container_end_page
container_issue 2
container_start_page
container_title Journal of pressure vessel technology
container_volume 136
creator Hyde, T. H
Hyde, C. J
Sun, W
description Many components in conventional and nuclear power plant, aero-engines, chemical plant etc., operate at temperatures which are high enough for creep to occur. These include plain pipes, pipe bends, branched pipes etc., the manufacture of such components may also require welds to be inserted in them. In most cases, only nominal operating conditions (i.e., pressure, temperatures, system load, etc.) are known and hence precise life predictions are not possible. Also, the proportion of life consumed will vary from position to position within a component and the plant. Hence, nondestructive techniques are adopted to assist in making decisions on whether to repair, continue operating or scrap certain components. One such approach is to use scoop samples removed from the components to make small creep test specimens, i.e., sub-size uniaxial creep test specimens, impression creep test specimens, small punch creep test specimens, and small ring (circular or elliptical) creep test specimens. Each specimen type has its own unique advantages and disadvantages and it may not be obvious which one is the most appropriate test method to use. This paper gives a brief description of each specimen and associated test type and describes their practical limitations. The suitability of each of the methods for determining “bulk” material properties is described and it is shown that an appropriate test type can be chosen.
doi_str_mv 10.1115/1.4025864
format Article
fullrecord <record><control><sourceid>asme_cross</sourceid><recordid>TN_cdi_crossref_primary_10_1115_1_4025864</recordid><sourceformat>XML</sourceformat><sourcesystem>PC</sourcesystem><sourcerecordid>477526</sourcerecordid><originalsourceid>FETCH-LOGICAL-a315t-cf14ec66e34e328f6fb67b866b3a3004dba3ca9eb6f786eced0067e6ab6ecded3</originalsourceid><addsrcrecordid>eNotkDtPwzAYRS0EEqEwMLN4ZUix42fGEPGoVMSQMFuO8xlS5SU7DP33BLXT1ZWOro4uQveUbCml4oluOcmElvwCJVRkOtW50pcoISTnaZ4zco1uYjwQQhkTNEG7Aj_b2EXsp4Ar6MEt3fiNlx_AH1NccDHPYZpDZxfA1WD7HlczuG6AEZcBYMY1rFR9nOEWXXnbR7g75wZ9vb7U5Xu6_3zblcU-tYyKJXWecnBSAuPAMu2lb6RqtJQNs4wQ3jaWOZtDI73SEhy0hEgF0jZraaFlG_R42nVhijGAN6veYMPRUGL-PzDUnD9Y2YcTa-MA5jD9hnFVM1wpkUn2B45wV7Y</addsrcrecordid><sourcetype>Aggregation Database</sourcetype><iscdi>true</iscdi><recordtype>article</recordtype></control><display><type>article</type><title>A Basis for Selecting the Most Appropriate Small Specimen Creep Test Type</title><source>ASME Transactions Journals (Current)</source><source>Alma/SFX Local Collection</source><creator>Hyde, T. H ; Hyde, C. J ; Sun, W</creator><creatorcontrib>Hyde, T. H ; Hyde, C. J ; Sun, W</creatorcontrib><description>Many components in conventional and nuclear power plant, aero-engines, chemical plant etc., operate at temperatures which are high enough for creep to occur. These include plain pipes, pipe bends, branched pipes etc., the manufacture of such components may also require welds to be inserted in them. In most cases, only nominal operating conditions (i.e., pressure, temperatures, system load, etc.) are known and hence precise life predictions are not possible. Also, the proportion of life consumed will vary from position to position within a component and the plant. Hence, nondestructive techniques are adopted to assist in making decisions on whether to repair, continue operating or scrap certain components. One such approach is to use scoop samples removed from the components to make small creep test specimens, i.e., sub-size uniaxial creep test specimens, impression creep test specimens, small punch creep test specimens, and small ring (circular or elliptical) creep test specimens. Each specimen type has its own unique advantages and disadvantages and it may not be obvious which one is the most appropriate test method to use. This paper gives a brief description of each specimen and associated test type and describes their practical limitations. The suitability of each of the methods for determining “bulk” material properties is described and it is shown that an appropriate test type can be chosen.</description><identifier>ISSN: 0094-9930</identifier><identifier>EISSN: 1528-8978</identifier><identifier>DOI: 10.1115/1.4025864</identifier><language>eng</language><publisher>ASME</publisher><ispartof>Journal of pressure vessel technology, 2014-04, Vol.136 (2)</ispartof><lds50>peer_reviewed</lds50><woscitedreferencessubscribed>false</woscitedreferencessubscribed><citedby>FETCH-LOGICAL-a315t-cf14ec66e34e328f6fb67b866b3a3004dba3ca9eb6f786eced0067e6ab6ecded3</citedby><cites>FETCH-LOGICAL-a315t-cf14ec66e34e328f6fb67b866b3a3004dba3ca9eb6f786eced0067e6ab6ecded3</cites></display><links><openurl>$$Topenurl_article</openurl><openurlfulltext>$$Topenurlfull_article</openurlfulltext><thumbnail>$$Tsyndetics_thumb_exl</thumbnail><link.rule.ids>314,780,784,27924,27925,38520</link.rule.ids></links><search><creatorcontrib>Hyde, T. H</creatorcontrib><creatorcontrib>Hyde, C. J</creatorcontrib><creatorcontrib>Sun, W</creatorcontrib><title>A Basis for Selecting the Most Appropriate Small Specimen Creep Test Type</title><title>Journal of pressure vessel technology</title><addtitle>J. Pressure Vessel Technol</addtitle><description>Many components in conventional and nuclear power plant, aero-engines, chemical plant etc., operate at temperatures which are high enough for creep to occur. These include plain pipes, pipe bends, branched pipes etc., the manufacture of such components may also require welds to be inserted in them. In most cases, only nominal operating conditions (i.e., pressure, temperatures, system load, etc.) are known and hence precise life predictions are not possible. Also, the proportion of life consumed will vary from position to position within a component and the plant. Hence, nondestructive techniques are adopted to assist in making decisions on whether to repair, continue operating or scrap certain components. One such approach is to use scoop samples removed from the components to make small creep test specimens, i.e., sub-size uniaxial creep test specimens, impression creep test specimens, small punch creep test specimens, and small ring (circular or elliptical) creep test specimens. Each specimen type has its own unique advantages and disadvantages and it may not be obvious which one is the most appropriate test method to use. This paper gives a brief description of each specimen and associated test type and describes their practical limitations. The suitability of each of the methods for determining “bulk” material properties is described and it is shown that an appropriate test type can be chosen.</description><issn>0094-9930</issn><issn>1528-8978</issn><fulltext>true</fulltext><rsrctype>article</rsrctype><creationdate>2014</creationdate><recordtype>article</recordtype><recordid>eNotkDtPwzAYRS0EEqEwMLN4ZUix42fGEPGoVMSQMFuO8xlS5SU7DP33BLXT1ZWOro4uQveUbCml4oluOcmElvwCJVRkOtW50pcoISTnaZ4zco1uYjwQQhkTNEG7Aj_b2EXsp4Ar6MEt3fiNlx_AH1NccDHPYZpDZxfA1WD7HlczuG6AEZcBYMY1rFR9nOEWXXnbR7g75wZ9vb7U5Xu6_3zblcU-tYyKJXWecnBSAuPAMu2lb6RqtJQNs4wQ3jaWOZtDI73SEhy0hEgF0jZraaFlG_R42nVhijGAN6veYMPRUGL-PzDUnD9Y2YcTa-MA5jD9hnFVM1wpkUn2B45wV7Y</recordid><startdate>20140401</startdate><enddate>20140401</enddate><creator>Hyde, T. H</creator><creator>Hyde, C. J</creator><creator>Sun, W</creator><general>ASME</general><scope>AAYXX</scope><scope>CITATION</scope></search><sort><creationdate>20140401</creationdate><title>A Basis for Selecting the Most Appropriate Small Specimen Creep Test Type</title><author>Hyde, T. H ; Hyde, C. J ; Sun, W</author></sort><facets><frbrtype>5</frbrtype><frbrgroupid>cdi_FETCH-LOGICAL-a315t-cf14ec66e34e328f6fb67b866b3a3004dba3ca9eb6f786eced0067e6ab6ecded3</frbrgroupid><rsrctype>articles</rsrctype><prefilter>articles</prefilter><language>eng</language><creationdate>2014</creationdate><toplevel>peer_reviewed</toplevel><toplevel>online_resources</toplevel><creatorcontrib>Hyde, T. H</creatorcontrib><creatorcontrib>Hyde, C. J</creatorcontrib><creatorcontrib>Sun, W</creatorcontrib><collection>CrossRef</collection><jtitle>Journal of pressure vessel technology</jtitle></facets><delivery><delcategory>Remote Search Resource</delcategory><fulltext>fulltext</fulltext></delivery><addata><au>Hyde, T. H</au><au>Hyde, C. J</au><au>Sun, W</au><format>journal</format><genre>article</genre><ristype>JOUR</ristype><atitle>A Basis for Selecting the Most Appropriate Small Specimen Creep Test Type</atitle><jtitle>Journal of pressure vessel technology</jtitle><stitle>J. Pressure Vessel Technol</stitle><date>2014-04-01</date><risdate>2014</risdate><volume>136</volume><issue>2</issue><issn>0094-9930</issn><eissn>1528-8978</eissn><abstract>Many components in conventional and nuclear power plant, aero-engines, chemical plant etc., operate at temperatures which are high enough for creep to occur. These include plain pipes, pipe bends, branched pipes etc., the manufacture of such components may also require welds to be inserted in them. In most cases, only nominal operating conditions (i.e., pressure, temperatures, system load, etc.) are known and hence precise life predictions are not possible. Also, the proportion of life consumed will vary from position to position within a component and the plant. Hence, nondestructive techniques are adopted to assist in making decisions on whether to repair, continue operating or scrap certain components. One such approach is to use scoop samples removed from the components to make small creep test specimens, i.e., sub-size uniaxial creep test specimens, impression creep test specimens, small punch creep test specimens, and small ring (circular or elliptical) creep test specimens. Each specimen type has its own unique advantages and disadvantages and it may not be obvious which one is the most appropriate test method to use. This paper gives a brief description of each specimen and associated test type and describes their practical limitations. The suitability of each of the methods for determining “bulk” material properties is described and it is shown that an appropriate test type can be chosen.</abstract><pub>ASME</pub><doi>10.1115/1.4025864</doi></addata></record>
fulltext fulltext
identifier ISSN: 0094-9930
ispartof Journal of pressure vessel technology, 2014-04, Vol.136 (2)
issn 0094-9930
1528-8978
language eng
recordid cdi_crossref_primary_10_1115_1_4025864
source ASME Transactions Journals (Current); Alma/SFX Local Collection
title A Basis for Selecting the Most Appropriate Small Specimen Creep Test Type
url https://sfx.bib-bvb.de/sfx_tum?ctx_ver=Z39.88-2004&ctx_enc=info:ofi/enc:UTF-8&ctx_tim=2024-12-24T22%3A07%3A11IST&url_ver=Z39.88-2004&url_ctx_fmt=infofi/fmt:kev:mtx:ctx&rfr_id=info:sid/primo.exlibrisgroup.com:primo3-Article-asme_cross&rft_val_fmt=info:ofi/fmt:kev:mtx:journal&rft.genre=article&rft.atitle=A%20Basis%20for%20Selecting%20the%20Most%20Appropriate%20Small%20Specimen%20Creep%20Test%20Type&rft.jtitle=Journal%20of%20pressure%20vessel%20technology&rft.au=Hyde,%20T.%20H&rft.date=2014-04-01&rft.volume=136&rft.issue=2&rft.issn=0094-9930&rft.eissn=1528-8978&rft_id=info:doi/10.1115/1.4025864&rft_dat=%3Casme_cross%3E477526%3C/asme_cross%3E%3Curl%3E%3C/url%3E&disable_directlink=true&sfx.directlink=off&sfx.report_link=0&rft_id=info:oai/&rft_id=info:pmid/&rfr_iscdi=true